Aktifit AM in molded gaskets, o-rings and radial shaft seals

Diamine (ACM, AEM)

Calcined product, amino functionalized.

Aktifit AM offers higher tensile strength, higher tensile modulus and lower compression set as well as better abrasion resistance and improved chemical resistances.

very low sieve residue

good mixing and dispersion properties

long flow time with short vulcanization time

easy deflashing

low compression set

good media resistance (fuel, oil, water, acid)

avoidance of mold fouling caused by filler

Product characteristics	Unit	Testing method	AKTIFIT AM
Functionalization			amino
Color values L* Color values a* Color values b*		acc. to CIELAB	96.2 - 0.1 1.0
Particle size D₅₀ Particle size D₉₇	µm	acc. to ISO 13320-1	2.3 11.0
Residue > 40 µm	mg/kg	acc. to DIN EN ISO 787 part 18	10
Volatile matter at 105 °C	%	acc. to DIN EN ISO 787 part 2	0.2
Density Bulk density Tamped density	g/cm³	acc. to DIN EN ISO 787 part 10 acc. to DIN ISO 903-1976 acc. to DIN EN ISO 787 part 11	2.6 0.31 0.55
Spec. Surface area (BET) Oil absorption	m²/g g/100 g	acc. to DIN ISO 9277 acc. to DIN EN ISO 787 part 5	9 65
Hardness silica/kaolinite	mg	acc. to Mohs	7/4.5
Refractive index n		sin α / sin β	1.55
Water solubility Acid solubility	%	acc. to DIN EN ISO 787 part 3 acc. to DIN 53770 (0,1 N HCL)	< 0.5 < 1
Chemical Analysis: SiO₂ Al₂O₃ Fe₂O₃	%	acc. to DIN 51001 (RFA)	86 13 < 1
Mineralogical Composition: Neuburg silica Calcined kaolinite	%	Based on X-ray diffraction pattern analysis combined with Rietveld	60 40
Equilibrium moisture content at 25°C and 50% relative humidity and 80% relative humidity and 90% relative humidity	%	acc. to DIN 66138	0.11 0.29 0.55
Water absorption	ml/g	acc. to Baumann	not specified
reactive			X

Molding / Light-colored

Gasket and O-Ring, Aktifit AM versus carbon black N-550, according to PSA S22 5106; 60 Shore A; AEM; diamine cure (M 621.4/2) (M 621.4/5) (M 621.4/3)
Gasket and O-Ring, Aktifit AM in combination with silica in AEM; 70/80 Shore A; AEM, diamine cure (AEM 9919) (AEM 9914)

Download all

Material Specification

In order to make available to you the most important information about our products at all times, you will find here the Material Specification.

The aspects to observe when working with our products are detailed in our Material Safety Data Sheet, which also can be downloaded.

All information about material characteristics, application fields and benefits can be found in this Technical Data Sheet and is also for download available here.

More recommended Products

Sorted by crosslinking agent.

Name	Short Description
SILLITIN N 75	Standard product for non-critical compounds with low requirements.
SILLITIN N 85	Standard product for slightly higher requirements for color and dispersion, low compression set.
SILLITIN Z 86	Standard product, less wear than Sillitin N products.
SILLIKOLLOID P 87	Higher tensile strength and tear resistance, least wear.
SILFIT Z 91	Same as N 85, but with avoidance of mold fouling caused by filler, greater brightness and color neutrality, less moisture content, improved dispersion, very fine cell structure in sponge rubber parts.

Name	Short Description
AKTISIL AM	Same as Silfit Z 91, but with higher tensile strength, higher tensile modulus and lower compression set, better abrasion resistance, improved resistance.
AKTIFIT AM	Same as Aktisil AM, but lower compression set.
AKTISIL PF 216	Highest tensile strength and tensile modulus, lowest compression set, best abrasion resistance, best chemical resistance.

Name	Short Description
AKTISIL VM 56	Same as Sillitin Z 86, but with higher tensile strength, higher tensile modulus and lower compression set, better abrasion resistance, improved chemical resistance.
AKTISIL VM 56/89	Same as Aktisil VM 56, but for greater color neutrality requirements and slightly improved dispersion.
AKTISIL Q	Similar to Aktisil VM 56/89 but with less moisture content, lower viscosity, lower compression set, improved resistance, best product for silicone rubber.
AKTIFIT VM	Same as Silfit Z 91, but with higher tensile strength, higher tensile modulus and lower compression set, better abrasion resistance, improved chemical resistance.
AKTIFIT Q	Same as Silfit Z 91, but with higher tensile strength, highest tension value and lowest compression set, better abrasion resistance, improved chemical resistance.